blog

Sat 21 Sep 2024

I really think it is time for a new 3D printer and I am doing my research.

Sun 4 Feb 2024

My Latest 3D Print Project It has been some time since I last 3D printed something, nothing too crazy, but certainly a couple of days. Getting back into my little 3D printing corner felt really good, back in the seat again ;-) OK, that was the intro of just getting into it all again. Additionally, I made some updates to the Raspberry Pi’s/OctoPi installations. I was also looking into slicer (Prusa slicer and Cura are my preferred slicers....

Thu 4 Jan 2024

Learning Shortcodes - rawhtml I am using the shortcode called rawhtml (note that it needs to be {{ … }}, skip the blanks, that was just something I had to do here) that is provided in the PaperMod theme: { {< rawhtml >} } <hr> <p>^And _here some <b>HTML</b> content...</p> <p align="center"><strong>This is raw HTML</strong></p> <hr> { {< /rawhtml >} } This is the result: And here some HTML content......

Wed 15 Nov 2023

This is explaining the process of a typical 3D printing process. Sharing some ideas, my specific setup and the tools that helps me. There is even a little video clip to enjoy ;-)

Mon 6 Nov 2023

OctoPrint Need Help In this article from All3D published 30th of October we learn that Gina Häussge, who is OctoPrint’s creator and full-time maintainer, has suffered a significant loss in funding. It’s that bad that without us chipping in it will be difficult to continue the project - one of the absolute main player in the 3D printing community. For Sure! We need to chip in and help Gina!

Sun 5 Nov 2023

The Nicest 3D Print assignment Today I am printing a little something for someone’s birthday. That is always the nicest things to print. It is currently, at the very moment when I am writing this, about 92% done. It’s a very nice type of 3D print job - only 1 hour and 21 minutes. The result doesn’t look too bad at all, some stringing, but not bad at all! Fingers crossed....

Sat 28 Oct 2023

A Little Follow-up So, during the last prints that I wrote about in the earlier post, I ran into an issue on the Prusa Mini+. All of a sudden, the Octoprint lost the connection to the printer. It might have happened before but then I just had to refresh or, at most, restart the page to fix it. This time I restarted the page during the print and then, even after the print was done, I tried to connect....

Sun 22 Oct 2023

Annoying… Yesterday when I was busy with 3D printing I ran all of a sudden into issues. While printing with the Prusa Mini+ printer I lost the connection between Octoprint (hosted on Raspberry Pi Zero 2 W). I noticed first on the web-frontend, that is how I monitor the progress. Raspberry Pi… I was going through the troubleshooting guide accessible from Octoprint. It did not resolve anything; it basically suggested changing the existing settings for Serial Port and Baudrate....

Sat 21 Oct 2023

Today’s 3D Printing Jobs Today I am running 2 3D print jobs at the same time, a cable winder organizer on the Creality Ender 3 v2 and then an airduct on (and for) my Prusa Mini+ printer. The cable winder job on the Ender printer had a difficult start, first layer was giving issues. It was sticking OK, but the problem was that it was pushing around surplus filament on the print bed....

Mon 16 Oct 2023

Adaptions I am busy doing some adaptions to this sites. I initially started designing it with the idea of replacing my Daily update site. But I started re-thinking that idea… How about if this could be the new IamPrinting.xyz site instead? Practical and Ideas Working with Hugo Working with Hugo and in Markdown brings some new challenges. Here below are the two ways of adding images and how to include HTML tags in Markdown....